Reverse Shoulder Replacement (Delta joint replacement) for arthritis: Surgery with a reverse prosthesis can lessen shoulder pain and improve function in shoulders with failed surgery or combined arthritis, rotator cuff tears and instability.

Edited By: Winston J. Warme, MD, Frederick A. Matsen III, M.D.
Last updated Friday, November 16, 2007

Figure 19

Figure 20

Figure 21

Figure 22

Figure 23

Figure 24

Figure 25

Figure 26

Figure 27

Figure 28

Figure 29

Figure 30

Figure 31

Figure 32

Figure 33

Figure 34

Figure 35

Figure 36

Figure 37

Figure 38

Figure 39

Figure 40

Figure 41

Figure 42

Figure 43

Figure 44

About the procedure

Technical details

Shoulder replacement surgery with a reversed (reverse Delta) prosthesis for cuff tear arthropathy complicated by instability is a highly technical procedure; each step plays a critical role in the outcome.

After the anesthetic has been administered and the shoulder is prepared, an incision is usually made across the side of the shoulder from above the collarbone to the middle of the arm bone as shown in the figure. [Figure 19] The deltoid is split along the direction of its fibers taking care to avoid the axillary nerve that runs on its inferior surface. Opening the shoulder reveals the irregular joint surface of the humeral head. [Figure 20] This surface is resected using a cutting guide. [Figure 21 and 22] Instead of duplicating the normal 30-degree posterior direction of the humeral head joint surface the head is cut so that it faces directly medially.[Figure 23 and 24]. The shaft of the arm bone (humerus) is prepared to receive the stem of the humeral component. [Figures 25, 26 and 27]. Additional reamers are used to prepare the neck of the humerus [Figures 28. 29, and 30]. The definitive humeral prosthesis body [Figure 31] is inserted into the prepared bone [Figure 32].

Attention is then directed to the glenoid, which is surgically exposed [Figure 33] and a pin driven into its center to act as a guide [Figure 34]. The glenoid surface is then drilled [Figure 35] and reamed to a flat surface [Figure 36]. The base of the socket (metaglene) is then inserted onto the prepared surface and fixed into position using four screws. [Figure 37]. The inferior and superior screws lock into the metaglene, while the anterior and posterior screws are not locking. [Figure 38]

A trial ball (glenosphere) is placed on the metaglene and a trial cup is placed on the humeral component allowing the surgeon to examine the shoulder for stability. [Figure 39 and 40]. If the soft tissue tension is insufficient for stability, an extended neck can be added to the humeral prosthesis [Figure 41 and 42].

Once the optimal trial components and the positions of the humeral and glenoid components verified, the definitive glenosphere is screwed onto the metaglene [Figure 43]. The definitive humeral socket is then fixed to the humeral prosthesis. [Figure 44]

At the conclusion of this procedure, the subscapularis tendon is securely repaired to the bone.

X-rays are taken to document the position and orientation of the prosthesis.

Links

• A video of the reversed (reverse Delta) prosthesis for rotator cuff tear arthropathy as performed by Dr Anders Ekelund of Stockholm Sweden can be seen here. (mpg, 15.2MB)
  
• A video of the reversed (reverse Delta) prosthesis for a previously failed shoulder arthroplasty as performed by Dr Anders Ekelund of Stockholm Sweden can be seen here. (mpg, 20.0MB)

Anesthetic

Length of reverse shoulder replacement

The procedure usually takes approximately two hours, however the preoperative preparation and the postoperative recovery may add several hours to this time. Individuals often spend two hours in the recovery room and two to four days in the hospital after surgery.

Surgery for Reverse Shoulder Replacement at the University of Washington

How useful was this page or article? This article is rated out of 5 stars (573 ratings). Not useful at all Not very useful Useful Very useful Extremely useful